We receive free products and receive commissions through our links. See disclosures page.

A few 12 months and a half ago, I made a decision to upgrade my low-cost squat stand to a sturdier and more versatile squat rack. After weeks of research trying to search out the most effective squat rack, I finally found one which met all of my requirements: the Titan Fitness X-3 Series Power Rack.

I continuously alternate between different training styles, including traditional strength training and CrossFit. As such, I knew I needed something that would accommodate various exercises. Amongst other things, I also wanted my latest squat rack to be within your means, stable without having to be bolted to the ground, and capable of survive in a non-temperature-controlled garage.

I’m completely satisfied to say that this power rack has handled every part I’ve thrown at it. On this Titan X-3 Power Rack review, I’ll discuss the development quality, durability, compatible attachments, and other features of this high-quality yet cheap power rack.

Key Takeaways

• Starting at slightly below $700, the Titan X-3 Power Rack is on the market in an 82-inch or 91-inch height. You may also choose from a flat-foot or a bolt-down design.
• This power rack consists of 11-gauge, 3×3 steel uprights and boasts a powerful 1,650-pound rackable weight capability.
• Titan offers a one-year warranty on the X-3 (and all of their products) for defects in materials or craftsmanship.

Titan Fitness X-3 Power Rack

4.0

• Dimensions: Footprint of fifty” x 48″; 82″ or 91″ height; 30″ inside depth
• Materials: 3×3, 11-gauge steel
• Weight capability: 1,650 kilos
• Hole spacing: Westside

Check Price

Titan X-3 Power Rack Pros

• The Titan X-3 flat-foot power rack doesn’t must be bolted to the ground and remains to be plenty stable. Note, though, that a bolt-down option is on the market in case you want extra peace of mind.
• The X-3 is cheaper than similar power racks in the marketplace, akin to Rogue Fitness’s R-3 Power Rack.

Titan X-3 Power Rack Cons

• There are not any laser-cut numbers on the uprights. Aligning the J-hooks on all sides will be annoying.
• The powder-coat finish isn’t the most effective for grip when hanging from the pull-up bar. You’ll wish to make certain you might have chalk or gymnastics grips close by for when your hands begin to sweat.

Titan X-3 Power Rack Specs

Price	Starts at $699.99
Footprint	50″ x 40″
Inside depth	30″
Material	3×3, 11-gauge steel
Finish	Powder coat
Weight capability	1,650 kilos
Hole spacing	Westside (one-inch spacing within the bench and rack pull zones; two inches above and below)
Included accessories	Two J-hooks lined with UHMW plastic; one 1.25-inch diameter pull-up bar; one two-inch diameter pull-up bar

Titan X-3 Power Rack Rating

The Breaking Muscle staff includes powerlifters, powerlifting coaches, certified personal trainers, and strength and conditioning coaches. It’s no surprise that we’ve a long time of experience with power racks. We even have a testing facility in Springfield, MO, where we put dozens of squat racks and power racks through the ringer. After testing them for several weeks (and months, in some cases), we rank them on a scale of 1 to 5 in various categories. Here’s how the Titan X-3 power rack stacked up.

Factor	Rating (out of 5)
Delivery and assembly	2
Materials and construction	4
Weight capability	5
Footprint	3.5
Hole spacing	5
Durability	4.5
Versatility	4.5
Attachments and accessories	3.5
Stability	5
Value	4.5
Warranty	3

Titan X-3 Power Rack Overview

The Titan Fitness X-3 Power Rack is a commercial-quality rack made with 11-gauge, 3×3 steel tubing. While it’s not low-cost, it may well still be a budget-friendly option for lifters who desire a reliable, durable power rack without spending hundreds of dollars. It’s rated at a 1,650-pound capability and encompasses a powder-coat finish to assist reduce corrosion and rust.

The Titan X-3 Power Rack on the Breaking Muscle testing facility

Two height options can be found — 82 or 91 inches — and you too can select a flat-foot or bolt-down design. Either way, the rack will remain stable and won’t wobble, even in case you perform kipping movements.

Who Should Buy the Titan X-3 Power Rack

• Individuals who train alone will likely feel safer squatting and bench pressing in an influence rack just like the X-3. This is particularly true in case you buy pin pipe safeties or safety straps.
• We predict home gym owners with low ceilings will appreciate that the X-3 is on the market in an 82-inch height. It should slot in most basements, as constructing codes in most areas require basement ceilings to be not less than seven feet (84 inches) high.
• As a result of its excellent stability, this power rack should work well for CrossFitters or functional fitness athletes who do a number of kipping movements.

Who Should Not Buy the Titan X-3 Power Rack

• Buyers preferring American-made products will wish to look elsewhere. The X-3 Series Power Rack is made in China.
• Those that don’t have large gym spaces should want to consider a more space-efficient option, like a foldable or wall-mounted squat rack.
• Individuals who move continuously should take a look at a more portable option like independent squat stands.

Titan X-3 Power Rack In-Depth Review

Having owned the Titan X-3 Series Power Rack for about 18 months, I’ve turn out to be vastly conversant in every aspect of it. I’ve used it for powerlifting-style training, general strength training, and CrossFit Workouts of the Day (WODs). The review below reflects my honest assessment of the way it ranks in multiple categories, including delivery, the assembly process, its functionality, and its overall value.

Delivery and Assembly

It’s hard for me to offer anything higher than 2 out of 5 stars for the delivery and assembly process. The rack arrived in multiple boxes, which is to be expected of something that has multiple heavy pieces. I didn’t appreciate that the majority of the boxes were damaged, nevertheless. Fortunately, the bottom, uprights, and pull-up bars were still in fine condition. Still, the poor packaging meant that I couldn’t give the rack high marks for delivery.

Another excuse I scored the Titan X-3 lower on this category is that the assembly process was long and difficult. This can also be something I expected, on condition that the rack weighs nearly 300 kilos. But it’s good to put aside not less than a few hours to place this unit together. I also recommend getting one other person to provide help to. The uprights will be cumbersome to administer by yourself, and it’s helpful to have assistance when installing the pull-up bars. It took my husband and me close to a few hours to totally assemble the rack.

Titan provides all of the bolts, screws, and washers you would like for assembly, but it’s good to have a socket wrench. Also, the instructions will be confusing in case you’re not handy. That said, so long as you might have a basic idea of what an influence rack should appear like (which you almost certainly do in case you’re considering buying one), it’s best to find a way to follow along pretty easily.

Materials and Construction

The Titan X-3 is made with 3×3, 11-gauge steel, which is typical of what you’d find in commercial-grade gym equipment. The welding looks sloppy in spots, but for my part, it’s not something to be concerned about. Unless you run a private training business out of your private home and/or want your equipment to look absolutely perfect, having some rough welds isn’t a giant deal.

Nonetheless, I’d have liked to see laser-cut numbers on the uprights. My old squat stand didn’t have them, and the rigs on the CrossFit box I used to belong to didn’t, either. It was annoying to must manually count the holes to get the J-hooks aligned. Not having numbered uprights can be frustrating in case you use other attachments that you just move around continuously, like safety straps.

Nonetheless, I discovered a workaround for this on the house gym sub-Reddit: using painter’s tape to mark the holes where you would like your J-cups for various lifts. I taped the uprights on my rack to point where I want my J-hooks for squats and bench presses. I even have tape by the holes where I put my safety straps for squats, bench presses, and rack pulls. The tape stays in place even after moving the J-hooks around. On the rare occasion when it does come off, it doesn’t leave a sticky residue behind.

Despite the fact that I’ve had success with this Band-Aid solution, I removed some points for the development and only scored it 4 out of 5 stars. Other power racks at an analogous price point, just like the REP Fitness PR-4000, have etched numbers on their uprights.

Weight Capability

The burden capability of the Titan X-3 Power Rack is 1,650 kilos. No person will ever find a way to lift anywhere near that, however the high rackable weight is sweet to see in a squat rack that costs lower than $800. It’s the very best weight capability I’ve seen in power racks designed for home gyms; some have 1,500-pound weight capacities, but most have 1,200-pound weight capacities. I gave the X-3 5 out of 5 stars for that reason.

Doing squats outside the Titan X-3 Power Rack

Footprint

There’s no denying it — Titan X-3 is a big piece of kit. It has a footprint of fifty inches by 48 inches, so it’s not ideal for super tight gym spaces. I knocked a couple of points off and only scored it 3 out of 5 stars since you would like a number of space to accommodate it. Along with the rack itself, you have to also be sure that you might have not less than a foot of space on all sides to load and unload weight plates out of your barbell. And if you need to do kipping pull-ups and toes-to-bar, you’ll need loads of space in front of the rack so you might have room to swing your legs.

Nonetheless, I do like you can choose from two different heights: 82 inches and 91 inches. The ceiling in my garage is about 94 inches high, so I opted for the rack with a 91-inch height. I’m 5’8 and have long legs and arms, and this height allows me to hold from the pull-up bar with my feet just barely touching the bottom. The 82-inch option can be suitable for shorter individuals and/or basement gyms with lower ceilings.

The within depth is 30 inches. It offers loads of room for me to walk out my back squat and doesn’t leave me feeling claustrophobic.

Hole Spacing

The Titan X-3 utilizes Westside hole spacing. The gap between the holes within the bench and the clean pull area is one inch; it’s two inches above and below that. Westside hole spacing is common within the better-quality power racks in the marketplace, just like the Rogue RML-390F Flat Foot Monster Lite Rack and the Bells of Steel Hydra 3×3 Half Rack.

The Westside hole spacing is a significant reason why I rated the facility rack 5 out of 5 stars on this category. The squat stand I had previously had one-inch hole spacing throughout. Each time I used to be bench pressing, I felt just like the rack height was just barely off. With the Westside hole spacing on the Titan X-3, I’m capable of set my barbell to a more precise height. Since I train alone, this helps make racking and unracking the bar much easier.

RELATED: Best Adjustable Dumbbells

Durability

I scored the Titan X-3 Power Rack 4.5 out of 5 stars for durability. I live in an area that gets hot and humid in the summertime and infrequently drops into the only digits within the winter. While I actually have heaters and fans in my garage gym, I only run them after I’m figuring out. Despite the variations in temperature and the moisture that always accumulates on my equipment when it’s humid, the rack hasn’t shown any signs of rust due to the powder-coat finish.

As well as, 3×3 11-gauge steel is super sturdy. And, as discussed above, it may well hold more weight than anyone can realistically lift, so that you don’t must worry about it collapsing during your workout and causing disastrous accidents.

Some minor scuff marks have appeared on the uprights over time, but I didn’t dock too many points due to that. In spite of everything, once you use something every single day, it’ll show not less than some signs of wear and tear and tear. Plus, the scuff marks don’t affect the steadiness or performance of the rack. I only point this out in case you’re expecting your rack to look pristine perpetually.

Versatility

Some of the vital aspects to me after I was looking for a latest squat rack was versatility. I am going through phases with my training. For the past 10 months, I’ve been primarily focused on CrossFit. Before that, I followed an upper/lower strength training split for years, though I still sprinkled in a few CrossFit WODs here and there. To that effect, I needed a rack that would handle quite a lot of movements — something that was lacking within the squat stand I had before, which was just like Titan’s T-3 Series Short Squat Stand.

A product tester doing pull-ups on the Titan X-3 Power Rack at our testing facility

Since I’ve had the Titan X-3, I’ve done traditional exercises like squats, bench presses, and overhead presses. I’ve been capable of do rack pulls by placing my safety straps in a low setting. For my CrossFit WODs, I’ve performed hanging knee raises, pull-ups, and ring rows (with a set of gymnastic rings that I had to buy individually). I’ve even set my barbell to a low height to establish a makeshift back extension station.

I also like knowing that I can add attachments to the Titan X-3 Power Rack in the longer term. Titan sells compatible attachments like a lat pulldown, a Y-dip station, and a leg curl/leg extension. The customization options put it on par with racks just like the REP PR-5000, the Force USA MyRack Modular Power Rack, and the Bells of Steel Hydra 3 X 3 Inch Flat Foot Power Rack. It scored a solid 4.5 out of 5 stars for versatility.

RELATED: Squat Stand vs. Power Rack: The best way to Select Your Gym’s Command Center

Attachments and Accessories

This power rack comes with two J-hooks lined with UHMW plastic (to forestall damage to your bar) and two pull-up bars: one with a 1.25-inch diameter and one with a two-inch diameter. Whenever you order your rack, you might have the choice so as to add plate storage pegs to your purchase for about $50 to $70 more. Based on my research, though, I made a decision to not get the burden plate holders. I read several customer complaints about plates stored on the pegs (especially bumper plates) getting in the way in which during bench presses. That was a headache I knew I wouldn’t wish to cope with.

As mentioned, Titan also sells dozens of add-ons for the X-3 series that allow for multiple configurations of your power rack. For instance, you’ll be able to get a lat pulldown attachment, dip bars, spotter arms, pin pipe safeties, monolift arms, a wall ball goal, and a battle rope anchor.

You may also purchase different J-hooks, akin to roller J-hooks, which assist you to slide the barbell and center it on the rack without damaging the knurling. I highly recommend swapping out the J-hooks that include the rack with a distinct pair. It only took a couple of workouts for me to appreciate that I hated the unique J-hooks. The lip comes up pretty high, and I used to be consistently hitting my barbell on it after I reracked the bar after squats and bench presses. But I couldn’t move the J-cups down a notch because then the bar position was too low for my liking. This is a component of the rationale I only gave the rack 3.5 stars on this category.

Nonetheless, what’s nice in regards to the X-3 Power Rack is its compatibility with attachments from other brands. For instance, I exploit safety straps from Rogue. I’ve seen several customer reviews online that questioned the standard of Titan’s safety straps, and I’m already paranoid about terrible things happening after I work out alone. For extra peace of mind, I selected safety straps with far more favorable reviews.

Stability

As discussed, the Titan X-3 Power Rack features 11-gauge steel with 3×3 tubing. It also weighs nearly 300 kilos and is rock solid. Titan sells the rack in a flat-foot or bolt-down design. I selected the flat-foot version because I didn’t wish to worry about potentially damaging my floor. I’ve never once felt the rack wobble or shake, so I scored it an ideal 5 out of 5 for stability.

Loading a barbell on the Titan X-3 Power Rack

Should you’re concerned about it tipping but still wish to go together with the flat foot design, you need to use heavy sandbags to weigh it down. For the record, though, I don’t think this can be a problem for nearly all of garage gym owners because that is such a beast of a rack.

Value

For around $700 to $800, I feel you get a number of value with the Titan X-3. The soundness and sturdiness are impressive. Plus, with all of the attachments you’ll be able to potentially add to it, it offers a ton of functionality.

After all, those attachments add to the whole cost of the rack. Nonetheless, you don’t must buy every part abruptly. You’ll be able to save up to buy add-ons one after the other until you might have the final word power rack for your private home gym.

One thing to notice is that Titan’s prices are reasonable partially because their products are made in China. Should you’d prefer to spend extra money on a US-made power rack, I like to recommend Rogue Fitness.

Warranty

The X-3 Power Rack comes with a one-year warranty. While this is healthier than nothing, I only gave it 3 out of 5 stars here. Other brands offer a lot better warranties. REP Fitness and Rogue Fitness, for instance, each offer limited lifetime warranties on their squat racks.

Titan X-3 Power Rack vs. Titan T-3 Power Rack

The T-3 Power Rack is one other one in every of Titan’s popular power racks. Just like the X-3, it uses 11-gauge steel. Nonetheless, while the X-3 uses 3×3 tubing, the T-3 uses 2×3 tubing. The T-3 isn’t as stable and wishes to be bolted down. Now we have the T-3 rack in our testing facility in Springfield, MO, and our product testers don’t recommend doing kipping movements or loading super heavy barbells on the rack unless it’s bolted.

The T-3 also has a lower rackable weight capability of 1,100 kilos, much lower than the X-3’s weight capability of 1,650 kilos. Still, nearly all of lifters won’t ever find a way to squat or bench press 1,100 kilos. The burden capability shouldn’t be a problem for many home gym owners.

You get more customization with the T-3. As an illustration, you’ll be able to select an interior rack depth of 24 or 36 inches. The X-3 is currently only available with an interior depth of 30 inches. Should you prefer more room to walk out your squat inside your rack, the T-3 rack with the 36-inch interior depth could also be a greater option.

The Titan T-3 Power Rack can also be a more suitable selection for budget-conscious lifters. It starts at slightly below $500, in comparison with the starting price of slightly below $700 for the X-3.

Titan T-3 Series Power Rack

4.3

• Dimensions: 46″ outside width; 24″ or 36″ inside depth; 82″ or 91″ height
• Materials: 2×3, 11-gauge steel
• Weight capability: 1,100 kilos
• Hole spacing: Westside

Check Price

Titan X-3 Power Rack vs. Rogue Monster Lite

Rogue offers several racks of their Monster Lite series, however the one closest to the Titan X-3 is the RML-390F. Just like the X-3, the RML 390-F boasts a flat-foot design that doesn’t require bolting to the ground. It’s also made with 3×3, 11-gauge steel uprights and has Westside hole spacing.

A advantage of the RML-390F is that it comes with pin pipe safety bars. The X-3 doesn’t include any safety pins or straps, so you might have to purchase them individually.

Alternatively, the RML-390F only comes with one pull-up bar in the usual 1.25-inch diameter. Nonetheless, I don’t think this is just too much of a drawback. If you need to occasionally do pull-ups on a thick bar to challenge your grip strength, you’ll be able to buy fat grips online. Using these grips is an affordable solution to increase the diameter of your pull-up bar — plus, you need to use them in your favorite barbell or set of dumbbells, too.

The RML-390F is manufactured in Columbus, OH. Due to this fact, it’s costlier than the Titan X-3. It starts at around $910, in comparison with the starting price of around $700 for the X-3. But in case you’re willing to pay more for an American-made product, the RML-390F might be a solid selection.

Titan X-3 Power Rack Customer Reviews

The flat-foot X-3 has 54 reviews and a mean of 4.7 stars out of 5 on Titan’s website. Customers are pleased with its ruggedness and love all the choices for add-ons and attachments. Those that left negative reviews noted that a few of the boxes were ripped upon delivery and wished that pin pipe safeties were included.

Final Verdict: Is the Titan X-3 Power Rack Price It?

As you’ll be able to probably tell from this Titan X-3 Power Rack review, I’m a giant fan. I purchased it when it became clear that I wouldn’t be returning to a industrial gym, and I’ve been pleased with my purchase. The rack is well-built and rugged — you shouldn’t must worry about any tipping or wobbling. Plus, with all of the attachment options available, you’ll be able to turn it into a flexible piece of kit.

Remember, though, that the X-3 is a big piece of home gym equipment. It has a footprint of fifty x 48 inches and weighs nearly 300 kilos. Before you hit that order button, measure and re-measure (after which re-measure again) to make sure you might have the space for it. Otherwise, you won’t find a way to reap the benefits of all the advantages of this durable, stable, and comparatively budget-friendly power rack.

FAQs

Does the Titan X-3 have to be bolted down?

The Titan X-3 flat-foot design doesn’t have to be bolted down. Nonetheless, Titan also offers the X-3 in a bolt-down version in case you want extra reassurance that the rack won’t tip or wobble.

What’s the opening spacing on the Titan X-3?

The Titan X-3 utilizes Westside hole spacing. The holes are spaced one inch apart through the bench press and clean pull area and two inches apart above and below that zone.

Is the Titan X-3 Power Rack product of steel?

The Titan X-3 Power Rack consists of three×3, 11-gauge steel.

Does the Titan X-3 have a pull-up bar?

The Titan X-3 comes with two pull-up bars. One bar has a 1.25-inch diameter, and the opposite has a two-inch diameter. You may also buy a multi-grip pull-up bar attachment individually.